Belonging category：Cremation equipment Publishing Date：20240114 views：7
Technical requirements of single-bed ash-picking cremator in funeral home cremation furnace;
1. Overall dimensions of the incinerator body: l× w× h = 3600× 2400× 2500mm (10mm).
2. The size of the main combustion chamber of the cremator: l× w× h ≥ 2500× 700× 800 mm.
3. The size of the secondary combustion chamber of the cremator: L×W×H≥2500mm×230mm×800mm.
4. Refractory material of cremation furnace: The whole combustion chamber is built with high-quality phosphate refractory bricks. The vault is built with one-time cast bricks. The mortar joint of refractory brick masonry is not more than 3mm, and the corner of bricklaying lap is bricklaying. The fire resistance temperature of the brick structure contacting the flame surface can reach 1200℃.
5. Thermal insulation material: The periphery of the combustion chamber is made of high-quality thermal insulation firebrick and aluminum silicate thermal insulation felt, which has good thermal insulation effect, and the average temperature of the furnace surface is not higher than 20℃.
6. Furnace frame: It is made of 304 stainless steel 40×40×2.5mm square tube, which is welded firmly and durable.
7. Exterior decoration of the furnace body: The gusset-type exterior decoration made of 304 stainless steel plate with a thickness of ≥1.0mm is beautiful and elegant, and it is easy to assemble and disassemble.
8. Combustion system: equipped with energy-saving dual-purpose burner and automatic ignition device, the burner angle can be adjusted up and down, and the combustion angle is 20 degrees. (Provide scheme)
9. Air supply system: The air supply pipeline is made of seamless stainless steel (thickness ≥3mm) with corrosion resistance and compressive strength (≥0.02MPA), which is embedded. After optimized design and layout, each air duct can form a strong vortex rotating air supply, and the air supply in the furnace has no dead angle, full combustion and good energy-saving and consumption-reducing effects. (Provide scheme)
10. Preheating system: It is made of stainless steel and installed above the vault of the combustion chamber, which can quickly raise the combustion air supply temperature to above 350℃ and accelerate the combustion and cremation.
11. Fuel supply system: All pipelines are made of special fuel seamless steel pipes, and all joints are sealed without leakage. And equipped with corresponding supporting devices.
12. Electrical control system: an independent electrical control cabinet is adopted, which has the functions of electrical protection such as overload and short circuit and comprehensive control of the system. Electrical components are made of high-quality brand products, and all cables are made of national standard brand products. All electrical components are installed by internationally accepted plug-in installation, which is beautiful and practical.
13. Cooling system: lifting cooling mode is adopted, and the average cooling time is about 5 ~ 10 minutes/set.
14. Cremator emergency system: It is operated by microswitch control panel control system.
15. Cremation furnace trolley and transmission system: The single-bed corpse delivery trolley is made of high-quality profiles and plates, and decorated with 304 stainless steel plates ≥1.0mm thick. Adopt mechanical transmission mode, controlled by motor and reducer, with stable operation, accurate positioning and low noise. (Provide supporting materials)
16. Inner oven door and lifting system: made of profiles and plates, embedded with high-temperature aluminum silicate refractory, with good sealing performance and excellent heat preservation effect. Adopt mechanical transmission switch mode, with stable operation and low noise.
17. Smoke exhaust system: lower smoke exhaust mode, Venturi injection, and the injection base and chimney are made of 304 stainless steel plates with high temperature resistance and corrosion resistance, with a thickness of not less than 2mm and a height of about 12m.
8. Pollutant emission index: It is used with tail gas treatment equipment, and all kinds of pollutant emission indexes meet the requirements of GB13801-2015 emission standard for air pollutants in crematoriums.